We offer affordable vinyl and luxury vinyl plank flooring, prefinished flooring,
unfinished flooring, and a broad range of molding, underlayment, and vents.
Choose from a full range of top-quality flooring tools and equipment. We have everything you’ll need to install, finish/refinish, and maintain beautiful hardwood, vinyl, and hybrid floors.
Panel Town & Floors is your one-stop shop for all your flooring supplies. From coatings, abrasives, and adhesives – to filler, putty, and subfloor preparation products – we have the highest-quality products.
***Certain colors may take up to 6 weeks to deliver***
Titebond WeatherMaster Sealant is a premium-grade, superior polymer formula that offers unbeatable adhesion to wood, vinyl siding, masonry, PVC, fiber-cement siding/trim and most common building materials. It can be extruded in low temperatures, remains permanently flexible with zero shrinkage, adheres well to damp surfaces, and provides a weatherproof seal against the elements. Available in over 200 colors, WeatherMaster matches today’s most popular siding colors, regardless of the material or manufacturer. When touch-ups are needed, this sealant can be painted within one hour with water-based paint.*
Seals: Siding, Windows, Doors, PVC, Glass, Fiberglass, Masonry, Wood, and Most Common Building Materials.
Joint Movement Capability ± 50%
Superior Polymer Technology
Applies In Extreme Weather Conditions
Fills Gaps Up To 1 Inch Wide
Remains Flexible – Will Not Crack
Uv-Resistant
Paintable In One Hour*
Voc-Compliant
Mold And Mildew Resistant
Compatible With All Types of Foam
Application Guidelines
Complete Installation Instructions: For complete installation instructions, please visit our Sealant Installation Guide for more information.
Application Temperature: Above 0°F (-18°C)
Service Temperature Range: -75°F. to 212°F (-59°C to 100°C) white & colors, -75°F to 250°F (-59°C to 121°C) crystal clear (may discolor at higher temperatures), -40°F to 400°F (-40°C to 204°C) translucent
Method Of Application: Cartridge/caulking gun
Tooling Time: For a 1/4″ bead, approximately 10-15 minutes, depending on temperature and humidity.
Application Directions: 1. Surfaces must be clean and free of any material that may prevent adequate adhesion. 2. Remove nozzle, cut tip of the nub and puncture inner foil seal. 3. Screw nozzle onto cartridge and cut tip on slant for 1/4″ to 3/8″ bead and place in cartridge gun. 4. Force sealant into clean joint. Always apply sealant in bead form. To ensure neat sealant lines, mask areas adjacent to joints. Once sealant is dry to the touch and does not transfer, remove masking tape. No tooling is required. It is the sole responsibility of the user to thoroughly test any proposed use with all substrates to determine project suitability.
Substrate Compatibility: If application is for Kynar™ coated materials, use WeatherMaster Metal Roof Sealant. For use on polycarbonate, check with polycarbonate supplier on compatibility. Do not apply WeatherMaster Translucent to polycarbonate due to solvent cracking.
Painting: Sealant is intended for exterior use. If used indoors, sealant may need to be painted. In most cases, painting may occur one hour after application with a high-quality acrylic, water-based (latex) paint that does not contain plasticizer. For other paint types, a compatibility test is recommended.
Cleanup: Clean uncured material with acetone or isopropyl alcohol. After curing, excess sealant must be cut or scraped away. Follow solvent vendor’s precautions when using solvents.
Coverage:
1/8” Bead: 116 ft.
1/4” Bead: 29 ft.
3/8” Bead: 13 ft.
1/2” Bead: 7 ft.
Limitations: Not designed for continuous submersion or use below the waterline. Air, sealant, and surface temperature should be above 0°F. Once sealant is applied, do not wipe with solvents or tooling aids such as soaps or oils. DO NOT TOOL – DO NOT SMEAR. It is highly recommended to use backing material. Application of sealant at high temperatures may cause the sealant to sag in some applications. Check with polycarbonate supplier on compatibility. Sealant releases methanol during cure, check with substrate manufacturer for compatibility. For best results, store in a dry location at or below 75°F. Contact with asphalt or butyl may cause discoloration, but will not affect product performance.
